How to add shock to an above ground pool

how to add shock to an above ground pool

How to Shock Your Above Ground Swimming Pool

How to Shock Your Above Ground Pool Clean your pool thoroughly BEFORE applying the shock treatment. Wait until the sun goes down to start the shock. The sun lowers the effectiveness of the shock chlorine. In a bucket, mix your pool shock chemicals into . Applying the Shock Treatment to your Pool With your filtration pump running, begin pouring the treatment into your pool. It’s best to begin sprinkling or pouring the shock slowly around your pool’s outer perimeter. As you do, try to avoid inhaling any fumes or particles that may get captured by the wind.

Shocking your pool is a great way to bring things back into balance. Yes, even salt pools need a little help once in a while. Salt water pools utilize a chlorine generator to convert salt into chlorine. You can adjust the generator to increase the level of chlorine produced to counteract higher chlorine demands caused by contaminants. However, even salt water pools need to be shocked when the generator cannot keep up with a heavy load of contamination.

Regular pool maintenance is essential for healthy, efficient, and economical pool operation. For best results, experts recommend shocking your pool when these circumstances occur:. Shocking your pool is a fairly simple process. Before you begin, uncover your pool, skim the pool, vacuum the sediment, and brush the walls, floor and coves. Free Chlorine: The desirable chlorine available to sanitize or disinfect the water. Combined Chlorine: Undesirable, bad-smelling chloramines that form when not enough free chlorine is present to overcome the chlorine demand.

Total Chlorine: The total amount which includes both free and combined chlorine. How Shocking your Pool Works Contaminants can get into pools and combine with chlorine. If the free chlorine level is not concentrated enough, it can cause the contaminant to become inert without fully removing it.

Combined chlorine or chloramines are ineffective in breaking down harmful bacteria and undesirable organisms. Shocking a pool elevates the free chlorine level to ppm. Elevated levels of free chlorine break up combined chlorine. Once your pool has been shocked, the water will be clean, clear, and safe for your family to enjoy.

Every how much to rent a flat of weeks during the swimming season. When your pool is outside of the recommended free chlorine levels of ppm. Shocking your pool will raise the chlorine level.

What about a salt pool? When should you shock your pool? This gives your pool plenty of time during the night to free the chlorine and clean the water.

In the morning, you should be able to enjoy your pool. Opening Day — Before the kids jump in for the new season, you should clean and shock your pool.

Over the winter or during times of disuse, algae have a tendency to grow. Make sure the pool water is clean, clear, and healthy for your family before opening day. Free chlorine levels drop dramatically after times of heavy use, so bring it back up to normal levels by shocking your pool. Stormy Weather — Spring and summer bring periods of high winds and heavy rains. Combat the changes in your pool water by cleaning your pool and adding how to play aom online. This will remove contaminants and bring the pH levels up.

Sunny Days— Summer brings the perfect pool weather! But when the days are hot and sunny for long periods of time, the pool water chemistry can be affected.

Bring your water chemistry back into balance. Shock your pool to break up the combined chlorine and release it back to free chlorine. When the time comes, think ahead by cleaning and shocking your pool. How do I shock my pool? Check that the pH levels in your pool are balanced Prepare shock ahead of time in a 5-gallon bucket of pool water and stir.

Ensure the pool pump is running. Pour the mixture from the bucket into the water around the edges of the pool.

Let the pump run for about 6 hours or more and test the water. When water tests okay, you are ready to go — dive right in! Sign up to receive our latest blog posts directly to your inbox! Featured Posts. All About Salt Chlorination.

Featured Posts

Pre-mix the pool shock in a five-gallon bucket. Ensure the pool pump is running. Pour the mixture into the water, around the edges of the pool. Let the pump run for about six hours or more. How do I shock my pool? Check that the pH levels in your pool are balanced Prepare shock ahead of time in a 5-gallon bucket of pool water and stir. Ensure the pool pump is running. Pour the mixture from the bucket into the water around the edges of the pool. Let the pump run for about 6 hours or. Aug 06,  · Matt teaches you how to shock your swimming pool the right way by pre-dissolving each pound of pool shock in a bucket of water before adding it to the water.

Keeping the pool water clean is a task next to impossible. Due to the wind, rain, and other natural aspects, pool water is bound to get dirty with dead leaves, branches, and other light materials like paper, tissues, and all. Then you have the sunlight, which is the prime food for algae to grow in the pool water. Lastly, a pool is for swimming, and your whole body is under the pool water. You might have put on body lotion, sunscreen and might be profusely sweating under the sun while playing in your above ground pool.

What if your toddler just peed right there. All these things are responsible for the water to react and get dirty. So, pool water needs a thorough cleaning with a proper process. Right beneath, we are going to step by step discuss how to shock an above ground pool.

If you have an above ground pool, it will be of great use for you. The first step is to know when exactly you need to shock the pool. Only a few dead leaves, pebbles, and branches here and there in the pool water will not require a shock to clean.

You can clean those with a skimmer only. If you are running the pool pump regularly and water circulation is constant, you might not need to shock the pool for a long time. However, it is good to shock your above ground pool once every fortnight to keep the water free of contaminants and stop algae from growing. Still, if you are too busy or lazy and not using the pool quite often, let us tell you that an above ground pool needs shock only when the water turns green, yellow, or black. You will know your pool water will turn green because, before that, you will see some ugly looking substance floating all over the pool water.

That is when your pool water is called cloudy. So, as we are discussing steps to shock the pool, we assume the water in your above ground pool is full of algae and dirt. Hence needs a shock. Testing the pool water means checking the pH, chlorine, and alkaline level. If the first two levels are at balance, the alkalinity level is not an issue. Yet it is better to stay on the safe side by keeping the water chemistry balanced. Alkaline controls pH and halts the water from turning too acidic.

When it is in the range of ppm, you know the alkalinity level is balanced. Pool water must have its pH level between 7. High pH levels and low chlorine levels both indicate the bad condition of the pool water.

Both allow algae to grow and turn the color green and perhaps even worse, to black. So, if the pool water needs a proper balance, add chemicals in it. Best is to balance it after the shock. Use a leaf net with a telescopic pole and clean the large dirt particles from the pool water. Leaves that are floating on the water, pebbles, and branches that are lying in the bottom of the above ground pool.

Skim all thoroughly. Now, get a brush to scrub the sides of the pool. To get into the bottom, you will need a brush with a long handle. Scrub the pool surface rigorously. Now, take a skimmer with a finer mesh and start straining all those small dirt particles. Pool shocks are heavily concentrated and come in a powder form.

A pack of pool shock weighs about one pound, and that is enough to shock a pool that contains gallons of water. So, a small above ground pool might not need a full pack. Follow the instructions written on the packet and be precise with the measurement. Take a bucket full of water. Dump the chlorine powder or pool shock in it. Use a stick to mix the chlorine in the water. Make sure you are wearing gloves and goggles as chlorine is a potent substance. Keep even a drop of chlorine mixed water away from your clothes; otherwise, it will get bleached.

Time to pour the chlorine water in the dirty pool water. But first, make sure your filtration pump is running. Pour the liquid treatment from every side of the pool. You will notice the difference in the water.

The chemistry happens right away. Best is to shock the pool at night so that you can keep it unused overnight. It takes 24 hours for a pool shock to properly cleanse the water and make it apt for swimming again. The whole procedure might end up in a cloudy pool.

Just use a pool clarifier to solve that issue. When you poured the treatment in the pool water, your pump was running, and it should continue running for the next 24 hours straight. If possible, a bit more. After your pool water returned to its crystal clear self, time to test the pH and chlorine level. For that you will need test strips. Both sodium carbonate and bicarbonate increases the pH level of pool water. And if the pH level needs a decrease just add sodium bisulfate.

The chlorine level will be in the typical range as you have already poured pool shock in it where the main ingredient is chlorine. Make sure to run the pump after balancing the pH by mixing the chemicals.

After waiting for a day or two, you can reuse your above ground pool. The wait is essential because the amount of chemicals you are using to refine it is as harmful as the dirty pool water to your body.

So, first let the pool water settle a bit, and then continue using it. Do not use a dirty above ground pool when the purifying process is this easy. Shock the pool regularly and keep it healthy for you and your loved ones. Regularly use of above ground pool vacuum to clean you pool. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. This site uses Akismet to reduce spam. Learn how your comment data is processed.

Skip to content Keeping the pool water clean is a task next to impossible. Leave a Comment Cancel Reply Your email address will not be published.

5 thoughts on “How to add shock to an above ground pool

Add a comment

Your email will not be published. Required fields are marked *